April 21, 2017

You asked for it: N75C-1 Coil (BOSTITCH)…


Graphs

How BOSTITCH N75C-1’s price changed over last several months:
You can see the trends in N75C-1 cost change
Nailer Sheathing/Siding Coil reviews compared with other similar products:
Coil Nailer Sheathing/Siding isn't that bad compared to other products

Info

Features:

  • Drives 15-degree wire weld collated and plastic inserted nails with shank diameters of 0.090-Inch to 0.131-Inch
  • Lightweight aluminum design for added durability
  • Adjustable depth guide sets nails to desired depths quickly and conveniently
  • Perfect for high-volume nailing of wall and roof sheathing
Other Info for this deal:

Warranty: standard manufacturer’s warranty
S&H: Free shipping if ordered online
Dimensions and weight: check our reviews
Coupon/Sale: n/a


General description

The N75C-1 – coil sheathing/siding nailer is perfect for high-volume nailing of wall and roof sheathing. It drives 15-degree wire weld collated and plastic put in nails with shank diameters of 0. 090 In. To 0. 131 In. It has a lightweight aluminum design for extra durability. An adjustable depth guide sets nails to wanted depths quickly and conveniently. Weight 4. 9 Lbs. 2. 22 kilos. Driving power 630 In. /Lbs. Fastener range 1-1/2 In. To 3 In. Wire weld and plastic put in coil nails (. 090 In. To. 131 In. Shank) magazine capacity 225-300 nails operating pressure 70-120 PSI thread fitting type 1/4 In. NPT.


Recent reviews of BOSTITCH N75C-1 Coil Sheathing/Siding Nailer:

The lite weight of this item is a real improvement over older models. My arms and shoulders loved using this on scaffolding and ladders. I sided a two story 1300 square foot garage using LP smartside. I used 2. 5 inch Hitachi nails. Of the 3000 nails I used I do not think I had more than two or three jams. The gun has lots of power for Smartside application.



This nail gun is plagued with important faults: 1) Poor nail depth control at less than 90 psi. 2) Poor nail cycling performace at less than 90 psi, 3) poor nail magazine design. I own some number of Stanley Bostitch nail guns and have found that the gas system on their coil nail guns can not cycle at the lower end of the particular operating range. This can be of little concern for simple wood fence installs but for difficult fiber cement installations, exactly those where fiber cement is directly installed over XPS bubble, the lack of finesse when driving nails makes the gun nearly useless. I was nailing plank fiber cement siding over 1" XPS bubble through OSB and into wall studs with 3" smooth shank nails (Bostitch C10P120DG). At 90+ psi, nails blew clean through the siding, with a fragile bump of the nosepiece on the plank surface. Adjusting the nail depth wheel to minimum didn’t fix the issue. Nails did advance properly although. At 70-80 psi, nail depth was controlled but nails could not advance. The work-around was to fire the nail in the chamber, move the gun to an area over the bubble sheathing, bump against the sheathing while firing and pushing nails to advance with left hand, fire siding, repeat. Literally every other nail could fire this way. Zero nails could fire otherwise. Totally disappointing. I have framing guns that will not fire at lower pressures either, however they do not have to, and do not promote operating at 70 psi, either. Lastly the nail magazine/chamber is seemingly suited for no more than 2 1/2" nails like its little brother (N66). The 3" nail barely fits in the chamber (driving end) and the magazine height will not let the nails to be domed up at all.



In spite of some of the negative reviews I bought this nail gun. It appealed to me because it’s able of shooting down to a 1 1/2" siding nail and up to a 3" framing nail. (two in one). I bought some 1 1/2" nails locally for a siding project I have and the gun could shoot one nail and not feed the next nail. I took the gun and nails to the place I bought the nails (a place that specializes in fasteners and nail guns, not big box) prepared to purchase a siding nailer they suggested. They asked to see the gun, although they don’t sell Bostitch they recognized the problem now. Not the gun but the nails. They clarified the wire spacing on the nail coil from one nail maker to another can differ somewhat. The solution was to grind down the teeth on the feed pawl of the gun to let for out of tolerance nails. They said it’s common to have to do this on all nail gun manufacturers. The gun now shoot flawlessly. The only reasons I didn’t give it five stars is Bostitch should have accounted for this variation in nails in the design of the gun and second I have only shoot the gun some times so do not know about the longevity of the gun. By the way place that fixed the gun was Southern Fastener in Oklahoma City. They did it free of charge, great people.




Compare with similar products:

Hitachi NV50AP Pneumatic Nailing System vs N75-C-1

Pays for itself in the N75C-1 1st job decreases labor cost up to 60. A new nailing system that removes hand nailing. Saves time and money Safer – frees up a hand 350 shots between reloads. From insulation sheathing to house wrap to roofing felt with the same tool – no modifications needed Each ProPac® holds 8 coils of 1-1/4- or 2-inch ring shank nails and 8 reels of collated Plasti-Top caps. 2,800 fasteners per Pro-Pac. Till now, the only way to drive plastic cap nails was by hand nailing with a hammer. Roofing freelancers point to that the Plasti-Tacker Pro system decreases the time required to dry-in a house by up to 60. Supported by a one-year warranty. Nails and caps not included.


Woodtek 965571, Portable Power Tools, Air, s, Miter And Clamp Jig Combo

Picture frame assembly made fast, easy and correct. The Woodtek 160-490 Picture Frame Jig in conjunction with the Woodtek 148-268 Picture Frame V corner nailer removes alignment and position variation inherent in hand held air nailers making picture frame assembly fast, correct, and easy: The Woodtek 148-268 hand held Picture Frame V corner nailer is securely held to the jig with four 3/8″ diameter rods and a 1/8″ thick metal plate configured to fit the screw pattern of the gun cylinder head lining up the gun to a perfect right angle with the worktable. The worktable table has a 90 fence that brackets the mitered corner and easily changes in and out to accommodate different molding widths. Stop collars incorporated into the 90 fence assembly lets repositioning of the molding for many fastener insertion in each mitered corner. The work is securely held with two lever activated clamps with rubber feet to hold the molding securely and without marring while the adjustable stock support arm (maximum length 12-1/2″ from miter tip) helps support long stock. The specially intended V Corner fasteners align with the grain to take benefit of the natural strength of the wood. As generally, our “No annoyance ensure” is behind each one of our merchandise. If for any reason you aren’t 100 pleased, simply return the merchandise inside 90 days of buy for an direct refund or substitute, as you ask. Imported and with a one year parts and workmanship warranty.


CN-350 B Duo-Fast O-ring Replacement Kit

Tool fix O-ring Kit for Duo-Fast Tools Each tool fix kit holds all the o-rings as listed to rebuild your tool. Unless otherwise noted, kits include quality Buna-N O-rings and seals equal to or the OEM parts. Duo-Fast CN-325B CN-350B O-ring Kit will include: 2 – 006-70L O-ring 1 – 010-60N O-ring 1 – 012-70L O-ring 1 – 013-70N O-ring 1 – 028-70L O-ring 1 – 040-90N O-ring 1 – 026-70L O-ring 2- 137-70L O-ring 3 – 142-70L O-ring 2 – 144-70L O-ring 1 – 146-70L O-ring O-ring Seal Kit – assembled with high quality, aftermarket parts that make up a complete o-ring seal kit.


N64C-1 Industrial Fencing / Siding vs N-75C-1

Features and Benefits :: Magnesium housing for job site durability fast-release canister for fast, easy loading Adjustable depth control for flush nailing Rubber grip for comfort Adjustable deflector conveniently directs exhaust High-affect composite canister survives falls big coil capacity holds up to 350 nails Product Details:: Height 12. 88″, Length 100. 56″, Width 5. 19″, Weight 5. 8 lbs, Driving Power 570 Magazine Capacity 350 Max. Operating Pressure 100 Min. Operating Pressure 70 Operating Pressure 70-100 Power to Weight percentage 98 Thread Fitting Type NPT Thread Size 1/4 Application : Wood siding Fiber cement siding Shingles Fencing Pallets and crating Decking Wood sheathing to light gauge steel.


Ouya BDQ-1 73-116 Psi Mini Pneumatic Pull

Application:Ouya mini pneumatic nail remover is widely used to take off nail from template, wood, and wooden case. Features:Light Weight with Aluminum body gun body. Steel Contact safety with dual carbide inserts for less wear. Soft grip for comfort and control. Design for easy operating. About seller:Ouya gives the best tools for industrial businesses, professionals, and buyers to make their life easier and successful. We offer high quality and professional merchandise from pneumatic tools, power tools, to hand tools for those who demand the best in cheap price. Specially, Ouya offers custom design for your spray gun, drill, nailer, and so on. Ouya became a reliable name in tools business. Our goal was simple: supply the best tools and solutions that make your life easier.


Makita AN611 1-1/4-Inch to 2-1/2-Inch Siding

The Makita AN611 1-1/4-Inch to 2-1/2-Inch Coil Siding Nailer features a non-slipping nose with an ideal form for diagonal nailing. Operating at 65 to 120 psi, this nailer features an easy-load canister for maximum versatility. Chose from either sequential or bounce fire with the nail-mode selector. A depth-setting handle means easy modification of nailing depth (9 settings in increments of 1/16-inch). This tool keeps itself clean with a smart, fitted air filtering system, and a rubber bumper protects tool housing. The included silent sheet assures no sound when disconnecting the coupler. The Makita AN611 includes a comfy rubber grip; a fitted air filter to prevent dust or foreign matter from entering the tool; a 360-degree exhaust system to direct exhaust away from the operator. Accessories that are included with the iMakita AN611 are; a Hex wrench 4 (783202-0); plastic tool case (824490-1); and safety goggles (192517-8). This nailer weighs 5 pounds.


Freeman PCN65 2-1/2-Inch Siding vs N-75-C-1

The Freemans PCN 65 Siding/Fencing coil nailer is the ideal tool for tackling cedar shingles, roof and wall sheathing, siding installation and fencing. This nailer shoots 15 degree nails ranging in size from 1" to 2 1/2". This gun is able of using wire or plastic collated nails, which removes rust streaks on siding and fencing installations. The body of this gun is constructed of die cast magnesium for low weight and durability. The comfy padded grip and ergonomically light weight design lets expanded daily use with less exhaustion. The Freeman PCN 65 comes with a easy side load canister and fast action makes this tool more economical. Freeman Pneumatic Nailers are constructed with only the best quality materials and protected by side and front affect bumpers. Each gun is tested before it’s accepted for shipping. Freeman Pneumatic Nailers is made under rigorous terms to ensure professional quality and is supported by a 7 year warranty.


Max CN565S2 Max Siding

The Max USA CN565S2 SuperSlider Siding Coil Nailer 1-1/4″ to 2-1/2″. The Max USA CN565S2 SuperSider siding coil nailer drives 15 degree wire collated nails from 1-1/2″ to 2-1/2″ in length, and plastic collated nails from 1-1/4″ to 2-1/2″ in length. Only 5 lbs and easy to manage for expanded periods of time. A maintenance free end cap filter to prevent dust and debris from entering the tool, easy-load magazine, adjustable depth of drive, adjustable exhaust, anti-double fire system, and non-marring contact tip. Applications: siding, fencing, outside trim, sheathing, subfloor, roof decking, outside decking and more.


Cases By Source TUC-11403-M Large Heavy Duty Tool Case with Universal Pallets

With more volume than the other TUC models, this tough and rugged but stylized case offers that much needed bit of extra space for your valued and treasured tool collection. The modular tool pallets offer flexibility for tools of varying shapes and sizes. The removable cover pallet has 3 modular sections (front and back) for tools up to 13/16″ diameter, and the tool pallet in the base of the case has 3 modular sections for tools up to 1 1/16″ diameter. The standout feature is the DIY movable dividers in the base of the case that gives a mass of possibilities for each possible need. Paperwork and blue-prints can be organized in the removable literature pouch. This tool case features 2 key latches, and a mix lock to ensure your tools and equipment are generally safe.


N66C-1 1-1/4-inch to 2-1/2-inch Siding with Aluminum Housing

Nail down siding in no time with the powerful, exact Bostitch N66C-1 Coil Siding Nailer. This lightweight tool features a aluminum housing that makes it lasting enough to frequently withstand the rigors of all-day use. And with adjustable nail depth and a soft rubber foot, you may be able to work with a range of siding materials, as well as soft woods. The N66C-1 Siding Nailer works with any air compressor and has a tool-free adjustable exhaust that directs spent air away from you when you are working. The Bostitch N66C-1 Coil Siding Nailer At a Glance: 515 in. /lbs. Of driving power Adjustable nail depth Lightweight, lasting aluminum housing Tool-free adjustable exhaust All-day siding jobs are easier on your hands thanks to lightweight magnesium housing. View bigger. Accepts both wire-weld and plastic-put in coil nails from 1. 25″ to 2. 5″. View bigger. Works with a range of Siding Materials, from Soft Wood to SteelPretty much regardless what kind of siding you are working with, the N66C-1 will take care of the job. This nailer accepts both wire-weld and plastic-put in coil nails and will include a soft rubber foot that is perfect for working with soft wood. Also, the N66C-1 can handle the tough stuff: cement, clapboard, fencing, and light-gauge steel are no problem. The N66C-1 has an adjustable guide and an operating range of 70 to 120 PSI, which means you may be able to dial in the right depth for the job. And with driving power of 515 in/lbs, the N66C-1 may be easily set for 1-1/4-inch to 2-1/2- inch nails. Also, the N66C-1 has a 350-nail magazine, so you may be able to knock out lots of work in a single load. The N66C-1 Siding Nailer works with any air compressor and has a tool-free adjustable exhaust that directs spent air away from you when you are working. Lightweight, lasting Construction for Everyday UseFinish the job without breaking a sweat. The N66C-1 Siding Nailer is constructed with aluminum, which means it’s light enough to wield all day. Measuring just 3. 25 x 12 x 11. 25 inches (WxHxL) and weighing just 4. 9 pounds, this nailer is still lasting enough to withstand the wear and tear of any jobsite. The N66C-1 stores in its included protecting carrying case when not used. The Bostitch N66C-1 Coil Siding Nailer is covered by a seven-year restricted warranty. About BostitchStanley-Bostitch manufactures top-quality, groundbreaking fastening tools and fasteners for industrial, construction, and home-improvement applications. Merchandise include pneumatic staplers and nailers; compressors; manual staplers and tackers; coil-fed screw systems; rivet tools; glue guns; a broad variety of collated nails, screws, staples and expertise fasteners in a range of materials and finishes; and box-closing staplers – many of them business firsts. What is in the BoxSiding nailer and carrying case.


Omega 10205B Black Hydraulic Bottle Jack – 20 Ton Capacity

Omega Side Pump Bottle Jacks Get Your Job Done with Ease Omega 10205B bottle jack is a 20 Ton side pump hydraulic bottle jack. With the bypass system fitted, it guards the hydraulic system from the interior damage. Its machined and polished cylinders with die cut threads supply non-abrasive leak free, lasting performance. Omega 10205B bottle jack is manufactured from hard cast steel with the heat-treated important stress regions. It includes the distinctive cross type forced release valve that assures positive load control. Also, it’s protected from overload. – Overload Protection – Machined and Polished Cylinders with Die – Cut Threads – manufactured from Hard Cast Steel with Heat Treated important Stress regions – Built – In Bypass system & distinctive Forged Released Valve – distinctive cross – type forged release valve assures positive load control plans -Capacity: 20 Ton – Base Size: 6-3/8″ x 5-7/8″ – Min Height: 9-7/8″ – Max Height: 18-7/8″ – Extension Screw: 3″ – GW: 28 Lbs Omega 10205B Bottle Jack is supported by the full one year warranty from the date of the buy. Click the button now to get Your Omega 10205B Black Hydraulic Bottle Jack.


Max CN70 1-3/4-Inch to 2-3/4-Inch Heavy Duty for Siding

The Max CN70 is lasting and its fastening speed is very fast. The CN70 was loved in industrial application for decades. CN70 SuperHeavy-responsibility Industrial Coil Nailer – Extra heavy-responsibility: Die cast aluminum construction. Rugged magazine. Drives 225-300 nails continuously by full-loading. Multi-directional exhaust. Comfy rubber grip. Equipped with dust cover and body protector. Use for: Making and repairing pallets, Crating, Fencing, Siding, decking and sheathing. MODEL CN70. FIRING technique Contact trip (sequential trip: Available by choice). WEIGHT 7. 6 lbs. (3. 5 kg). DIMENSIONS 12-7/16″(H) x 5″(W) x 12-1/16″(L) (315 x 128 x 306mm). LOAD CAPACITY 225 – 300 nails. OPERATING PRESSURE 70-100 psi (5-7 kg/cm2) (Regulator). AIR intake 0. 053ft3 (1. 5lit)/cycle at 90 psi (6 kg/cm2). Use with: Drives from 1-3/4″ x. 092″ up to 2-3/4″ x. 113″ (45mm x 2. 3mm – 70mm x 2. 9mm) 15 flat wire welded nails.



What people considered before buying N75C1:
  1. Bostitch BTFP72333 Industrial 1/4-Inch Series Swivel Plug with 1/4-Inch NPT Male Thread
  2. BOSTITCH C6R90BDG 2-by-0.090-Inch Thickcoat Ring Shank by 15-Degree Coil Siding Nail, 3600-Per Box
  3. PacTool International SA903 2-Piece Gecko Gauge Hardi Board Siding Gauges
  4. BOSTITCH C8R90BDG Thickcoat 2-1/2-Inch by .090-Inch 15 Degree Ring Shank Coil Siding Nail (3,600 per Box)
  5. PacTool International SA90338 Gecko Gauge
  6. BOSTITCH RN46-1 3/4-Inch to 1-3/4-Inch Coil Roofing Nailer


Models to consider:
N66C-1 CN70N64C1 PCN65TUC-11403-M NV65AH2
N66BC-1 DW66C-1RCN55-15 R112M611NV50AA CN565S2
NV65AH S225AM1675S13A125SNBP S205A1AN611 530A
CN565S AN611-RS13A250SNBP NV50APHCN57PA 10205B
S13A175SNBP AN610HCF152 BDQ-1
AN610H S225AM1675HCN57PA S205A1PCN65 NV50AP
DW66C-1R NV65AHN66C-1 S13A175SNBPAN611-R 530A
NV50AA R112M611BDQ-1 TUC-11403-M10205B S13A125SNBP
CN70 CN565S2CN55-15 CF152AN611 N64C1
CN565S NV65AH2N66BC-1 S13A250SNBP
DW66C-1R CN70NV65AH N66BC-1HCN57PA S205A1
S13A175SNBP TUC-11403-MBDQ-1 S13A125SNBPNV65AH2 N64C1
CF152 S225AM1675S13A250SNBP 10205BCN55-15 AN610H
NV50AA NV50APAN611 530ACN565S2 R112M611
AN611-R CN565SN66C-1 PCN65

Subscribe

Subscribe to N75C1 best prices tracker for your city/stores

Select area


Select Store


Product Versions:


Email: