Check this out about Jet Pump (Flotec) reviews
- Enter your model number above to make sure this fits.
- Vertical Deep Water Well Jet Pump
Warranty: standard manufacturer’s warranty
S&H: Free shipping if ordered online
Dimensions and weight: check our reviews
May be used in 4″ diameter or bigger wells up to 260′, or in 2″ diameter wells up to 180′. Key Features: Superior performance at depths to water of 50′ or more. Rugged, heavy-responsibility cast iron pump housing. Prepared-to-install 230 volt motor – see manual for 115 volt conversion. Flow at 50′ lift and 40 psi: 11 GPM. AMP Draw (full load): 9. 6 amps on 230V/19. 2 amps on 115V. /suggested Breaker 15 amp for 230V/ 20 amp for 115V. No. FP4432: Size: 1 HP, Material: Cast Iron, Capacity: 12 GPM Maximum, Suction Size: 1-1/4″ NPT, Discharge Size: 1″ NPT, Maximum Lift: 260′ for 4″ or bigger well/180′ for 2″, Voltage: 230V/115V, 60 Hz, Warranty: 1 year restricted, Pkg Qty: 1, Package Type: Box.
Sentry 822 PS
Here is How Pump Sentry FP4432 Works Battery Back Up For Sump Pumps 1200 Watt Capacity 822PS Pump Sentry interfaces between a pump and its AC wall outlet. When AC utility power is present, the 822PS charges a battery and monitors the wall outlet to detect a power outage. Now utility power fails, the 822PS draws energy from a battery and changes it to enable pump operation. When utility power returns, the 822PS automatically switches the pump back to AC wall outlet power. Simultaneously, the 822PS resumes charging the battery to return it to full capacity in preparation for the next power failure. Pump Sentry interfaces between a pump and the AC electrical supply. When electricity is available, Pump Sentry charges a battery and monitors the power line to detect a power outage. At the instant that power failure occurs, Pump Sentry draws the energy stored in the battery and changes it to AC power. This AC power is automatically channeled to the pump to preserve its operation in the lack of electricity. When AC utility power is restored, the Pump Sentry reinstates AC utility power as the prime energy source to operate the pump. At the same time and automatically Pump Sentry commences the recharging of the battery, to return it to full capacity in preparation for the next power failure. Intended to operate most 1/3 Hp. Sump pumps made by: Hydromatic Jacuzzi Stevens Zoeller Tecumseh Wayne.
Ironmate Submersible Sump – 400 GPH, 3/4, /2in., Model# FPS4550A
Features lasting cast-iron volute and motor housing, tough polycarbonate impeller and thermally protected, oil-filled motor. Vertical float switch gives dependable operation and lets installation in 10in. Basins. High-capacity 1 1/2in. NPT discharge. Will replace most pedestal pumps with no plumbing changes. UL listed. U. S. A. Flow (GPH): 4,100, Volts: 115, Amps: 20, HP: 1/2, Max. Total Head (ft. ): 15, Discharge Port (in. ): 1 1/4, Min. Basin Needed (in. ): 10, Pump Housing: Cast Iron, Volute: Cast Iron, Impeller Shaft: Polycarbonate, Power Cord (ft. ): 10, Dimensions L x W x H (in. ): 12 3/4 x 10 x 12 3/4.
Fp7230-08 Vertical Epoxy Lined Tank, 42 Gallon
Highlights: Replaces any standard galvanized, glass-lined or epoxy-lined tank Precision press fit design minimizes gaps between parts, decreasing the possibility of corrosion and seam leaks. Tough polyester outside paint. Air volume control tap standard on all sizes plans: Body construction: Heavy gauge steel Body finish: Electrostatically applied baked on polyester Style: Vertical upright Tank capacity: 42 gallon Tank diameter: 16″ Tank height: 53-1/2″ Pipe tap size: 1-1/4″ NPT.
Red Lion RLSP-50 -/2- 50- Cast Iron Sprinkler vs FP-4432
Ideal for use in underground or above ground lawn sprinkling systems, garden irrigation, boosting household water pressure, and recirculation of big volumes of water. Heavy-responsibility cast iron pump housing engineered for high-efficiency – calm operation and rust and corrosion tolerant. 115/230 volt heavy responsibility motor with voltage selector lets for simple connection to present power source. Self-priming design – after initial fill, no extra priming obliged throughout operation. 71 GPM.
Star Water Systems Lawn Sprinkler – 4500 GPH, 2, Model# HSP20P
This Star Water Systems Lawn Sprinkler Pump is ideal for lawn sprinkler or irrigation uses. The 2 HP hand-wound copper wire motor easily handles a 25-foot suction lift. U. S. A. Flow GPH 4,500, Hose Adapters in. No, HP 2, Discharge Port in. 1 1/2, Port Size in. 2, Self-Priming Yes, Suction Port in. 2, Max. PSI 48, Max. Suction Lift ft. 25, Max. Total Head ft. 150, Volts 115/230. Fast self-priming operation 2 HP hand-wound copper wire ball bearing motor Cast iron pump Dual voltage operation 115V or 230V Supports up to 20 2. 0 GPM spray-type sprinkler heads per zone Easy-access drain plug big capacity 2in. Inlet suction pipe 1 1/2in. Discharge pipe.
MK Deep Cycle Gel Cell 2 Volt Battery for Backup Sump s
Our best battery for use in Marine situations and especially strong for use in the Backup Sump Pump business. This design will out-last the best Marine Deep Cycle batteries. For the power you need WHEN you need it, this is the one to purchase. It holds its charge longer and can handle the demands of the best back up sump pumps. If using direct 12 Volt back-up systems, or connecting through a power inverter, this battery has the reserve capacity to keep going long after other batteries have quit. When in comparison to regular deep cycle batteries, this one requires no maintenance and lasts 2-3 times as long. When the others die in 3 years or less, this one lasts 5-10 years with 7-8 years on average.
/2 2" Manual Submersible Sewage 5V
‘Submersible Sewage Pump, Manual, 1/2 HP, Switch Type None, Base Material Cast Iron, Housing Material Cast Iron, Impeller Material Cast Iron, Voltage 115, Phase 1, Amps 15, Height 21-3/16 In. Diameter 12-7/8 In. Cord Length 15 ft. Max. Dia. Solids 2 In. GPM of Water 5 Ft. Of Head 140, GPM of Water 10 Ft. Of Head 124, Max. Head 42 ft. Thermal Protection Yes, Motor Type Hermetically-Sealed, Oil-Filled, Bearing Type Ball, Shaft Seal Carbon/Ceramic, Agency Compliance UL Listed, CSA Certified’.
Taco 006-IQBC4 Bronze Smart Plus /2-Inch Sweat with Line Cord and Electronic Smart Timer
Using state-of-the-art electronics, the Smart Plus will monitor and record the home’s hot water handling pattern for the 1st week (7 days) of operation. For the next 7 days, the Smart Plus repeats the last week’s handling pattern to cycle the pump, instant hot water at all fixtures only when needed. This procedure will be repeated every 7 days. An optional “Pulse” mode may be selected which sets the Smart Plus to run for 150 seconds every 10 minutes maintaining hot water at all fixtures.
BACOENG 3/4” 0V/5V Hot Water Circulation /Circulator For Solar Heater System With US Plug
Performance Data: 1. Model:RS15-6G 2. Rated Power(W):93/67/46 3. Inlet/Outlet:3/4″ 4. Max Flow（l/min）:50/35/21 5. Max Head(FT):20/17/10 6. Voltage/Frequency/60HZ 7. Materials:Pump housing: Cast Iron Impeller: Corrosion-tolerant, Composite, PES Shaft: Ceramic Bearing: Carbon axial 8. Motor Feature:Single phase,Closed, externally ventilated Heavy responsibility Motor housing (will not get overheat uninterrupted running) Insulation class: F Protection class: IP44 Application: Used in suited for city buildings, suburban villas, houses, water and pressurized with industrial equipment, air conditioning, boilers, solar circulating water, hot water circulating warm and so on. Benefits: 1. High temperature resistance, anti-fraying, high efficiency, high flow,leak-tightness, low intake 2. Super silent, environmental protection, aesthetics, ease of installation. 3. Fitted high sensitive electronic sensors, the water flow when we open the switch. Specification 1. Suited for Medium: hot water and ethanol maximum percentage of 1:1 2. Performance: Liquid temperature range:-10 – +110 Celsius,Maximum working pressure:10bar 3. Ambient Temperature: Not higher than 40 Celsius. 4. Mounting Position: Shaft horizontal mounting 5. Pump Settings: single-phase pipeline pump 3 files manually controlled single-phase motor isn’t overloaded casting pump length 130 mm.
Zoeller M63 PREMIUM SERIES 5 Year Warranty Mighty-mate Submersible Sump, /3 by Zoeller
5-year warranty Float-operated, submersible, 2-pole mechanical switch integrating advanced switch technology Corrosion-tolerant, powder-coated epoxy finish All cast iron construction Viton outer switch boot No sheet metal parts to rust or corrode Stainless steel screws, switch arm, guard and handle No screens to clog Watertight, neoprene square ring between motor and pump housing hard, buoyant, polypropylene float Oil-filled, hermetically-sealed, auto reset thermal overload protected motor Upper and lower sleeve bearings running in bath of oil complete unit pressure-tested after assembly Carbon and ceramic shaft seal Maximum temperature for effluent or dewatering: 130 F (54 C) Passes (13 mm) spherical solids 1 NPT discharge On point: 7 (18 cm) Off point: 3 (8 cm) big width: 10-3/32″ (26. 2 cm) big height: 10-1/16″ (25. 6 cm) Watertight and dust-tight Permanently oiled bearings Cast iron impeller.
Liberty s 442-25A 25 Amp Standard Model StormCell 2V Battery Backup System
Liberty is introducing the l-series. A professional-grade line of battery backup pump systems called stormcell these systems feature high-output pumping, an energy economical dc pump for longer run times and professional-grade charger/controllers. They’re also available with optional nighteye technology for remote monitoring and notifications The line of stormcell merchandise also will include high performance 12 volt batteries that are USA made and intended for optimum performance in backup pump applications These batteries are available in group 27 or group 31 and in flooded or agm styles.
/2 Sewage PH, 5V 0ft Cord
NON-auto – Requires Float Switch or Controller Submersible Cast Iron Sewage Pump A workhorse for residential and light commercial sewage apps. Heavy-responsibility Epoxy Powder Coated Cast Iron Construction intended to offer years of dependable performance Rugged and Thermally Protected 1/2 HP Motor Hermetically sealed, permanently lubricated design Engineered 2-Vane Semi-Open HYTREL Polymer Impeller Corrosion-tolerant design, passes spherical solids up to 2″ High Capacity 2″ Discharge Will replace most pumps without any plumbing changes fast-Disconnect 10′ Power Cord lets for easy substitute of cord without breaking motor seals Stainless Steel Rotor Shaft with Unitized Ceramic Carbon Seal With permanently lubricated bearings for expanded pump life Non-Corrosive Stainless Steel and Brass Fasteners Increases the lifespan of the pump in the harshest systems 3-Year restricted Warranty.
- JET PUMP 1HP VERT MULTI (Discontinued by Manufacturer)
- Goulds SJ10 1 HP Vertical Deep Well, Multi-Stage Jet Pump
- Sta-Rite MSF 1 1/2 H.P. 1/115-220V, Vertical Multi-Stage Deep Well Jet Pump.
Models to consider:
|THD1035 FPUS1860A||2807CE72 F33SSS||SKHD150M6 20 20S-CIM|
|2400-20-WB FPSE3601A-04||5HS2S100 DFK-961||SKHS200M2 30 BW1050|
|VIR393A95 8-CIM 25FT||FPSC3250A FP0S2450A-01||FPH4 4LE12|
|PH3000 CV-114/112||3205C 4KHF9||6PY34 D175120T|
|PS1000 SPD100MH2 20||2RLAG-1 6RLAG-3ST||SPRK-1-ML 3310P|
|2810E FPSS1200X||PSSP10001VD 3E-12NR||FG-100A-01 GE65B|
|003-BC4 EPD-5AS1||822 PS KTV2-22||FP0S2400A-03 006-BC4-PNP|
|VIR201602878 3110P||LE51M 006-BC7-IFC||VIR201602571 66000-WYN1|
|2205C 3YU75||RJSE-50 HS3.75S||WX10TA 9SN-CIM|
|FPSC3250A SPD50MH1 20||VIR201602726 KTV2-22||SHEF40A1 EPD-5MS1|
|11AA RL-SPS33||4KHK3 FP0S2400A-03||2210C 5-ASP|
|3BB73 RH1400||PSSP10001VD FP0S1250X-02||8-CBA 20S-CIM|
|ESP25 WRSC-6||35-OM VIRRPP50||HSPJ20B1 3110P|
|12F738 2865G||A5000 1600C||3307P GE65B|
|5760-IPT-95 SD50A1 10||LBT-800 58325-WYN1||VIR201602632 N292|
|003-B4 US01+WH003221||2805E CB1500||F33SSS VIR201602571|
|2400-20-WB 003-BC4||DFK-961 WX10TA||DS3HF-01 LSG202A|
|VIR201602878 FP0S2450A-01||SPD100AH2 CV-114/112||008-CT-USK 2810E|
|2E-38N BW4000||HB1000 HE12-051-10||E75VLT 3E-12NR|
|FPSS1200X 006-BC7-IFC||3110P SPD100AH2||LSG202A HSPJ20B1|
|2RLAG-1 SHEF45M2 20||CV-114/112 EPD-5MS1||SW33A1 20 6RLAG-3ST|
|RH1400 OSP50BRA1 10||2400-20-WB WX10TA||SF-1100-PTSI HB1000-AVB|
|5-MSP 3305P||SKHS100A2 20 2807CE72||003-B4 SW50A1 10|
|1210C 006-BC4-PNP||58112-WYN2 FG-100A-01||20S-CIM 3307P|
|FP0S2400A-03 CB1500||HS3.75S 4KHF9||BP21X VIR393A95|
|RL12G07-2W2V 2865G||SD50A1 10 3YU75||3310P PS-C22|
|4810S 8-CBM||FPSC3250A FP0S1250X-02||DS3HF-01 VIR201602632|